Friday, August 30, 2019

Boarded Book Case

I recently got back from a trip to the US, and I have to write a catch-up blog or two. I made a couple of things there and I think I should blog about them.

This, however, isn't one of those blogs.

Right before I left, I was commissioned to build a boarded book case. I just finished it and I think it turned out very well.
Finished book case. I wish I could take better pictures of it. None of the pics I have seem to do it justice.
The client needed a bookshelf for his children's books. He gave me the measurements of his biggest books, and I came up with the design for this particular piece. I borrowed heavily from Christopher Schwarz's boarded book case in the Anarchist's Design Book.

I decided to make it about 80 cm wide and about 91 cm high (why not?).

I used some of my favorite plastic-wrapped laminated pine from the home center. I really like the stuff here because it is a good quality, and the laminations always are full-length. There are no end-to-end laminations in this stuff. Also, I can usually find boards that are mostly straight and have few knots.

Since it was intended to be used with kids, I borrowed one of my wife's pot lids from the kitchen to lay out a roundover on the top front edges. If I forget to mention it later, I cut it out with my Dick saw, clamped the pieces together, and cleaned everything up with a spokeshave and a rasp.

I started this project out by cutting the boards to length according to my cut list. Then I went to work on the dadoes.
I cut dadoes with my Dick saw, chop the waste out roughly with a chisel, then finish them with a router plane.
A while back I bought an old Record 071 rabbet plane from eBay. I've generally been happy with it, but there was a little crack in the very edge of the blade that prevented me from getting it as sharp as I'd like. While I was in the US I picked up a set of Veritas replacement blades. It turns out they fit perfectly by dropping them in. I was able to sharpen the regular wide flat blade with no trouble to a very sharp edge.
I would recommend this upgrade to Lee Valley blades if you can.
Once that was done, I drilled pilot holes and temporarily screwed the book case carcass together with some cheap screws.
The idea behind using screws here is to replace them with Roman nails after I paint, for an even paint job.
I made a slight design change here from what was in the book. Instead of making 1/2" rabbets for the back boards to be inset, I used the same 3/4" laminated pine boards for the back, nailed flush rather than inset. My thought was it would give me an extra 3/4" of depth on the shelves.

Plus, it was easier.

In theory.

It turns out that once I got to this point, I realized the boards I had for the back were about a half inch to an inch too short. If I nailed them flush with the top of the bookcase, there was a gap before the board got to the bottom shelf. Ooops!

To fix this I decided to glue and screw a backer to the cross-rail that I had already inset into the top of the case. It was about half the width of that cross rail, so the back boards now go from that extension all the way beyond the bottom shelf so it looks just fine.

As an added benefit, there is a lot less endgrain showing on the top of the case now. Only a little on the sides that has been painted.
Gluing my necessity-invented backer extender thingie.
I didn't bother ripping the back boards to width before I nailed them on with no glue. I centered them the best I could, then I ripped the extra off after it was nailed on.
I planed all the sticky-out parts flush with the carcass.
Since the back boards don't go all the way to the bottom, I decided that I would count this as a feature: it leaves a little space so the shelf can be pushed up against the wall without having to muck with the baseboards. To make it look right, I just trimmed a triangle shape on the bottom so it looks like a 45 degree cut from the side.
This leaves room for baseboards.
I left gluing the toe-kick for last. I actually forgot to account for this piece when buying wood, so I had to use a piece of scrap pine that I pulled out of a dumpster. The color on it was far different than the rest of the piece, so I painted it before gluing it on.
Gluing on the toe-kick. Once it was clamped up, I drilled pilot holes and nailed it from the side.
One thing I did before gluing on the toe-kick was to put two coats of a commercial chalk paint on the sides. I lightly sanded it with a maroon scrubby pad after each coat, to keep everything nice and smooth.

Once the paint was on, I could replace the screws with Roman nails. The large heads of these nails cover up any evidence of the screws.
Putting a nail in a screw-hole.
I don't always do the screw before nail trick. It does add a little time, and one also risks really messing up the paint job with an errant hammer blow. These dents can be fixed on bare wood a lot easier. That is, as long as they aren't too bad.

Luckily I only had one French mark on this case, and it wasn't too severe. If my client doesn't read this blog, he will never know.

All that was left at this point was to chamfer the sharp bits and add a coat or two of BLO.
I used a block plane for the chamfers.
It was easy enough that I didn't really have a problem on this round part.
Once everything was done, I applied BLO with a paint brush, let it sit a few minutes and then wiped it down with paper towels. I started on the inside and did the painted parts last.
The oil really put a nice finish on this chalk paint.
This chalk paint covered nicely in one coat with no need for a primer. I used two coats, however, just to make sure that I wouldn't rub through the paint during this stage.
I slathered oil on the nails and everything. I would only suggest not to rub the paint too hard as some of the paint does come up once it's been drenched in oil. After wiping the oil down, my towels had plenty of paint on them.
I put some paint on my carved detail, but didn't bother with painting the back.
After the oil is on, the shelf looks really good. I decided to have the client come over and take a look at it before I bother to wax this piece. Wax can go right over the BLO after a week or so when it is cured. It probably could go on it after a day.
I think it turned out well, and I am glad I spent the time to make every little joint the best that I could. This book shelf isn't perfect, by any means, but I was happy to sign my name on it. Hopefully the client will get many years of enjoyment from it.

10 comments:

  1. Without a handle, how do you grip your Dick saw, Brian?

    A 3/4" back does add an extra bit of weight. I'd be happier with something much less than that, say 1/2" or even 3/8". That would cut the weight of the back by... oh... about half! lol.

    Do you happen to know how similar the Record 071 is to the Stanley 071? Do the Veritas blades fit the Stanley as well, is the question I need answered. I also need to add a small base to mine because no matter how many times I check the bottom for flat and smooth all edges with a bit of filing, I still get dinging on my wood surface.

    I wonder how Odie's Oil would look on milk paint. I'll have to give it a go.

    Great job on the bookcase, by the way. Looks fantastic!

    Cheers,
    Ethan

    ReplyDelete
    Replies
    1. Hey Ethan, thanks for the comment! I guess I didn't elaborate, but I cut the dados by clamping a batten across the grain and using it as a fence. When I do that with the Dick saw, the handle is in the way, so I take it off. This cut takes very little pressure. I've never hurt myself this way - yet.

      I can't really speak about the Stanley vs. Record, as I don't know it. However, I came up with the idea because people with the Stanley used the Veritas blade successfully. The Veritas blade's shank is remarkably longer, but you can mitigate that by flipping the adjustment but upside down. If you use a wooden base, even better.

      I always use oil and/or wax over milk paint with good results. I've never tried Odie's oil, though. I'll have to get some one of these days.

      Cheers!

      Delete
  2. Good thinking on the back, both top and bottom. The design additions look good. Seeing screws so close to where you planed still makes me cringe, you're a better planer than me! If no one makes copper or aluminum screws, brass would probably work. Other than snapping off too easily.

    ReplyDelete
    Replies
    1. Hey, Jeff! Thanks for the comment. Honestly I didn't really think about damaging my plane. But now you mention it, it does look close! I did make sure all of the screwheads were tightened down enough so the head was a little below the surface. That seems to work in pine.

      Delete
  3. Very well done Brian! I’m glad to read that others occasionally miss a part or miscalculate and have to design on the fly. I really like the sharp lines delineating the painted surface from the natural surface. Well done!

    ReplyDelete
    Replies
    1. Thanks, Ray! I used to despair over what I thought was a catastrophic mistake. I've learned over time that there is always an answer, it just takes a calm mind to think through the problem. I'm also really pleased with those sharp lines. I feared the paint would chip when planed, but this stuff is really nice. FYI, it's Rust-Oleum chalk paint applied with a brush.

      Cheers!

      Delete
    2. I really like how the bookcase turned out! Nice touch on the rounded corners, you saved some parents a bit of baby-stress there. Looking forward to seeing your blog posts about the other stuff you made. Oh, and more No.4 smoothing planes, please! :-)

      Delete
    3. Haha, Thanks Rudy!

      Rounded corners is something that can easily be done with furniture intended for rooms with kids. When I was a pre-school director, we were forbidden from buying any furniture that didn't have rounded corners.

      Isn't it about time for an update on your blog?

      Delete
    4. Hi Brian,

      Yeah, an update is long overdue! But I am working on one...

      Delete